KitchenAid Repair Kitchener

FZ Sensor Error: The FZ sensor has shorted or is open. 

R Sensor Error: The R sensor has shorted or is open.

FZ DEF Sensor Error: the DEF sensor has shorted or is open.

R DEF Sensor Error: The DEF sensor has shorted or is open.

Ambient Sensor Error: The ambient sensor has shorted or is open.

Flex Sensor Error: The flex sensor has shorted or is open.

Humidity Sensor Error: The humidity sensor has shorted or is open.

IM Sensor Error: The IM sensor has shorted or is open.

ICE RM Sensor Error: the ICE sensor has shorted or is open.

FZ Fan Error: The freezer fan is being read as not running or not connected.

R Fan Error: The Ref fan motor is not running or is not connected.

C Fan Error: The Comp. fan motor is being read as it as not working or is not connected. 

FZ Def Function Error: The freezer defrost heater is continuously heating for more than 80 minutes or is stuck open.

R Def Function Error: The fridge defrost heater is being read as running longer than 80 minutes or is open.

IM Function Error: The ice machine release heater is being read as being in open circuit.

Relay Stuck on Control Board: Turn off the power to the dishwasher for at least 5 minutes. If the code still appears, it is likely bad wiring or the control board needs to be replaced.

Damaged or Corrupted Memory on Control Board: Check the wiring between the keypad and the main control board for any loose and damaged wires. If no damage is found, replace the main control board.

Stuck Button on the User Interface Control

User Control Interface Not Communicating with Control Board: Check the wiring between the user interface and the main control board for any loose and damaged wires. If no damage is found, replace the main control board or user interface.

Thermistor/OWI Sensor Failure: Turn off the power and check the wiring between the thermistor and the main control board. Replace any damaged wiring, if no damage is found - replace the thermistor or main control board.

Error Between Electronic Control Board and Circulation Pump Motor: Disconnect from power and check the wiring between the circulation pump and the main control board. If no issues with the wiring are found, replace the motor assembly or the circulation pump.

Door Switch Failure: this code appears if the door is not shut 4 seconds after pressing the start key. If the door is shut, there may be a problem with the door switch, and must be replaced.

Door Not Opening Detected: The dishwasher expects the door to be opened before a new cycle begins. This code will appear if a second cycle is ran without opening the door. If this is not the case, the door switch may need to be replaced.

Dishwasher Won't Fill: Check for any items that may be stuck between the overfill float and the dishwasher and remove them. If the overfill float is stuck up, it will not fill.

Failure with Water Inlet Valve: Unplug the dishwasher from power and remove the toe panel and bottom front panel. Check the wiring harness for the water inlet valve. Repair any broken or loose wires or replace the harness.

Suds or Air Detected in Water Pump: This error code will appear when too much detergent has been used and there are too many suds in the dishwasher. For 3 minutes, the drain pump will run to remove the excess suds. If there are still suds, they will have to be removed by hand.

Float Switch is Open: Check the overflow switch and ensure nothing is blocking it or that it is not stuck. When the dishwasher is shut off, check to make sure that the water inlet valve is properly closing.

Incoming Water is Too Cold: This code will appear if the temperature is below 110 F. The normal temperature is between 110 and 120 F. You may need to replace the thermistor/OWI or the control board.

Heating Element Not Working: Unplug from power and look at the heating element for any damage. Replace if necessary. If no damage, check the wiring and replace the harness if needed.

Heating Element Not Shutting Off: Unplug from power for 5 minutes and see if the code clears itself. If not, the control board must be replaced.

Draining Slow: Unplug from power and turn off the water valve. Check drain hoses for blockages and remove them. If the hose is clear, check the drain pump' wiring for any loose or damaged wires. Replaced the drain pump.

Drain Pump Error: Unplug from power and shut off the water. Check the drain pump for any damage and replace if necessary. 

Electronic Control Board Cannot Detect Diverter Disc Position: Unplug from power and check the diverter disc's wiring. Replace or repair any loose or damaged wires. If no issues are found with the wiring, replace the wiring harness, control board, or diverter disc.

Diverter Motor Stuck On: This code indicates that the diverter relay is defective and needs to be replaced on the control board.

Diverter Disc Missing: Check the diverter disk for damage and replace.

Lower Spray Arm Error: Check for any obstructions blocking the lower spray arm from moving. If no blockages, check the wiring between the spray arm and the control board.

Detergent Dispenser Error: Unplug from power and check the wiring between the control board and the detergent dispenser. Replace the dispenser if no issues are found.

Vent Wax Moto Electrical Error: Unplug from power and check the wiring between the motor circuit and control board. Replace the vent wax motor if no issues are found.

Drying Fan Error: Disconnect from power and check the wiring between the drying fan and the control panel. Replace the drying fan if no issues are found.